UV Spot Light Source Curing Equipment UV LED Irradiation Machine 365nm 110V-240V

Description

template
UV LED Irradiation machine UV spot light source curing machine 365nm
Note:
There are two different choice of the UV Irradiation head,
t
he  item we send to you according to your choice.
One choice is 10mm+12mm Spot Light, the other one choice is 10mm+12mm+10mm+12mm  spot light,  please choose the right spot light what you need.
UV Curing Machine Operational Approach :
1.Preparation for startup.
Before using this device, please connect the foot  switch, irradiation head and power cord as required, and note that the  irradiation head cannot turn on the power switch to the person. Definition of  pedal switch wiring: GND common point, (CH1/ CH2/ CH3/ CH4/ separately  controlled, CH overall control,) do not insert and pull hard when the  irradiating head is inserted, just insert it by rotating to find the correct  direction. Hold the shrapnel at the terminal connector of the irradiating head.
2.Exposure Mode : compare pages after startup
CH1    100%A      10.0s
Normal exposure  mode
CH1    100%M      10.0s
Normal exposure  mode
CH1    100%p       10.0s
Normal exposure  mode
CH1    100%p       10.0s
Normal exposure  mode
3.Parameter Setting :
Press the SET key (READY lamp turns red) to enter the setting page. SET key  ACTS as the cursor movement key and sets brightness percentage and time data  through the direction key up and down. After setting, press the ESC key to save  and exit.
Note:
when the time is set to 0 seconds, the light source enters the normal  lighting state. The foot pedal is pressed to light the lamp, loosen to put out  the lamp. Select up and down key (1/U,2/L,3/D,4/R), press down and the LED light  will turn on. Press again and turn off the LED. Total open can be performed by  EMISSION.
4.Channel control mode :
（1）Push the Key : using direction keys of panel for each channel
（2）Pedal Mode : after connecting with pedal and through the PULSE setting up.
In order to reach high limit compatibility, Foot-Switch connector can connect  with Foot-Switch, as well as PLC, MCU, Supervisory Computer of I/O. The signal  of low -level output voltage continues more than 50ms.
（3）Serial Port
In addition, the machine will provide RS232 Serial Port, though RS232 connector  of the back panel.
Specification:
Name
UV LED Spot Light  Source
Type
UV LED
CURING-4II
Wavelength
365nm
UV Irradiation  head
1-
4
UV Irradiation  Mode
Light Spot
（
Φ
1.5
-Φ
20
mm
，
90°light  side irradiation or linear light spot
）
Irradiation  Distance
According to  light spot of
Operation Mode
AUTO   MANU    PULSE
Power
0-100%
Light Intensity
9900mW/cm2
Cooling Method
Pure Aluminum  Shell  Natural Cooling  Fan Cooling
Supply Voltage
DC
7.5-36V
Power Consumption
50VA
Ambient  Temperature
+5- +40℃
Ambient Humidity
20-60%
Size
L: 166mm   W:  100mm   H: 138mm
Weigh
2.5kg
Caution :
1.Package and Transport
When transporting equipment, use random packing materials. Any damage caused by  improper packing equipment is not not under warranty.
2.Daily Use and Maintain
LED irradiation head is needed be cleaned regularly. Please use soft buckskin,  lens paper and alcohol to clean, ensuring the irradiation intensity and good  heat dissipation.
Cleaning the controller regularly. Please wipe with a little alcohol with a  cleaning tool. In order to protect the surface of facility, don’t use the  volatile liquid or having ammonium hydroxide ingredient to clean (diluent or  benzene, etc.).
What  in Package:
1  x UV Spot Light Source Curing Equipment
(Note: The UV Irradiation head  we send to you according to your choice)
1.Your valid phone number is very necessary for the shipping, otherwise we can't guarantee that the package would safely arrives.
2. Any Customs tax applied to this package should be covered by buyers.
3. As has been stated on the eBay item description, Import duties, taxes and charges are not included in the item price and shipping charges. These charges be at the buyer responsibility, meanwhile the customs tax depend on the buyer  local customs office.
Contact Us:
1. We have always been trying to provide the best service and reliable products for every customer, however,  accident may happen sometimes, please contact us to resolve any issue before leaving a negative feedback.
2. Please contact us by "Ask a question".
Payment
1. Payment methods accepted:
Paypal
only
.
2. Payment must be received within 7 business days of auction closing.
Shipping
1. We ship your orders within 1-2 business days after the payment received.
2. Item shipped via Singapore Post or HongKong Post, It takes about 7-14 business days (USA,CA,AU,UK). Others country 10-20 business days (Brzil,India,RU), Exact delivery time depends on postal process.
3. If you do not receive your item(s) by 30 business days, Please feel free to contact us via ebay mail system, we will try our very best to resolve any problems with you.
Return Policy
1. Return is accepted within 14 days after the buyer's receiving the item.
2. If this item is defective upon receipt, customer has up to 14 days from date of receipt  for exchange of a new one.
3. Unused/unopened merchandise will be fully credited.
Other Policies
We are not responsible for any custom duty or import tax.
If you need we write low price on shipping bill, pls leave message when you make payment.
All emails will be answered within 24 hours. If you do not receive our reply, please kindly re-sent your email and we will reply to you as soon as  possible, Suggest send eBay message to  us, that is easy to find.